Denim Cubed Bracelet - DIY Jewelry Making Tutorial by PotomacBeads

Summary of the tutorial / subtitles

This video is a DIY jewelry-making tutorial for creating a “denim cubed” bracelet using crazy-lace look gemstone beads and matte metallic cube seed beads. The bracelet is built using a repeating box/square (St. Petersburg stitch) structure.

The maker constructs one side first, then reverses thread direction to build the opposite side while keeping the pattern aligned. The design is finished with wire guards, reinforced threading at wire guard points, and a clasp attached with jump rings.

Artistic techniques, concepts, and creative process shown

• Bead weaving / thread-based beading to form a structured, geometric pattern.
• Building repeating cube “box” units (squares created by threading back through specific cube bead positions).
• St. Petersburg stitch concept, adapted to this bracelet:
  • Creating a stable framework of cube beads.
  • Changing thread direction at the top to run “down the line.”
  • Placing small accent seed beads between gemstone beads.
• Alternating materials to match the “denim” look and add texture:
  • 4 mm round blue crazy lace gemstones as focal elements.
  • 1.8 mm cube beads (matte metallic blue-green iris) as the grid/frame.
  • 15/0 silver labrador full seed beads as highlights between gemstones/cube rows.
• Bracelet construction approach:
  • Building the band to the desired length.
  • Reinforcing wire guard areas with extra passes through gemstones/cube beads for durability.
• Assembly:
  • Attaching the clasp using jump rings.

Materials mentioned (as used in the tutorial)

• 4 mm round blue crazy lace gemstones
• 1.8 mm cube beads (matte metallic blue-green iris)
• 15/0 silver labrador full seed beads
• Beading thread (size stated: size six, green)
• Beading needle (size 11; suggestion to switch to size 12 if needed)
• Wire guards
• Jump rings
• Clasp (chosen by the maker)

Clear step list / process (from the subtitles)

1) Create a starting stop-bead

• Thread on 1 cube bead to act as a stop bead.
• Leave a couple inches of tail thread.

2) Build the first side pattern

• Add 5 cube beads, pushing them down to the stop bead.
• Weave back through cube beads 3 and 4 to form a cube box/square.
• Repeat the sequence:
  • Add cube beads (often in groups of 4)
  • Weave back through the first two to close the square
  • Add one 15/0, then go down three cube beads
  • Add a 4 mm gemstone and go back up the side cubes

3) Work to the desired bracelet length

• Demo indicates 27 gemstones.
• From wire guard to wire guard: 6.5 inches.

4) Change thread direction (St. Petersburg stitch adaptation)

• At the top, reposition thread so it runs down the center line of gemstones.
• Add 15/0 seed beads between each gemstone while running down.

5) Build the return side (“arms” / matching structure)

• Work back upward using repeated square formations:
  • Add cube beads (e.g., 6 at one point to recreate the square setup)
  • Add 15/0 accents between cube rows and gemstone tops
  • Repeat the “square + seed bead + gemstone top” rhythm until reaching the end

6) Attach and reinforce wire guards (end construction)

• In the last section, pass thread through/around the wire guard along with cube beads and anchoring passes through gemstones.
• Do extra weaving through the gemstone and cube beads to reinforce stress points.
• Repeat reinforcement at the opposite end.

7) Finish

• Tie off with knots described as right over left, left over right.
• Cut and burn off excess ends (as stated).
• Attach the clasp using jump rings.

Contributors / creators featured

• Chris — the instructor/maker (speaks as “Hello everyone. I’m Chris…”)
• PotomacBeads — creator/brand credited in the video title and throughout the subtitles

No other person’s name is explicitly featured beyond Chris.