Video summary

The new Einstar 2 and RockIt! Do these new scanners move 3D scanning forward?

Main summary

Key takeaways

Product Review

Product Overview

Both the Shining 3D Einstar 2 and Einstar Rocket are dual-mode handheld scanners with infrared (NIR) and blue-laser scanning. Both support wireless use through Wi-Fi and lithium-ion batteries, and both use Shining 3D’s EXStar Hub software.

Calibration is quick, with clear on-screen instructions. Each scanner comes in a soft-shell case with space for the scanner, accessories, batteries, charger, cables, calibration board, and board stand.

Einstar 2

The Einstar 2 uses 17 parallel blue-laser lines for laser scanning. Its infrared scans were praised for being quick and easy, with no markers required. It captured greasy engine and gearbox parts, as well as black plastic, without scanning spray.

On a Mini body, it captured the front end and bonnet in feature-alignment mode in one pass. The reviewer felt it had a slightly wider field of view than the Rocket, though settings may have contributed to the difference.

Laser mode provides finer detail and accuracy than infrared. At roughly €1,200, the reviewer considered the Einstar 2 strong value.

Einstar Rocket

The Rocket adds two laser options: 38 cross lines for faster scanning and seven parallel lines for finer detail and deeper holes. Its laser scanning captured data somewhat faster than the Einstar 2.

The reviewer found the Rocket’s infrared mode particularly effective at reaching into the inlet tracts of a manifold.

The Rocket also offers markerless laser scanning using feature alignment. This worked on an engine, but the scan had holes and became noisy at very fine resolution. The reviewer considered the technology promising but said it still needed software development.

In feature-alignment mode, the Rocket did not quite scan across the Mini’s full bonnet. Adding blue tape markers and using hybrid feature-and-texture alignment solved the issue.

Scanning Results and User Experience

The reviewer called the laser scans of a suspension upright the best scans of that part he had produced. The Rocket was a little quicker, while both scanners aligned and merged scans reliably.

Infrared scans were slightly less detailed than laser scans but required less effort and no markers. Both scanners handled a black plastic manifold successfully, though the Rocket had fewer initial issues.

Scanning the greasy engine was described as exceptionally easy: tracking remained stable, with no misalignments. The infrared scan was suitable for checking fit and clearances, though not for absolute precision. The Einstar 2 also produced a good infrared gearbox scan despite dirt and grease; fine accuracy around a flange might require laser scanning.

Point-cloud settings affect the results. The garage scans were intentionally made at relatively low resolution, so some details appeared soft.

Accuracy Test

After warming both scanners to the test environment and recalibrating them, the reviewer measured the following:

Scanner 1-2-3 block: 1 inch 1-2-3 block: 3 inches Micrometer: 56 mm Micrometer: 92 mm Rocket 0.01 mm error 0.03 mm error 0.02 mm error 0.03 mm error Einstar 2 0.02 mm error 0.04 mm error 0.2 mm error* 0.03 mm error

*The subtitle reports 0.2 mm over 56 mm for the Einstar 2.

The reviewer considered both scanners highly accurate for their price. The small differences did not establish that one was definitively more accurate, and repeated tests would be needed for a reliable comparison.

Software

Early software versions were glitchy, lagged, crashed, and made it difficult to get good scans. By the time of filming, the reviewer said most problems had been fixed. Across versions 8.4 and 8.5, he saw fast scanning—up to about 70–80 frames per second—and one crash.

He praised the software’s scan-cleanup tools, frame rewind, plane detection, scan alignment, meshing, measurement tools, and ability to orient a part using fitted planes. Shining 3D released another update during editing, leading the reviewer to expect ongoing improvements.

Verdict and Recommendation

The reviewer felt both scanners advance the consumer-grade category by combining easy tracking with very strong accuracy.

The Einstar 2 is his recommendation for most users. Its infrared mode alone would be useful, and the added laser mode makes it versatile. The Rocket is a better fit for power users who want faster or more extensive laser capture, the extra detail mode, or markerless laser scanning. Its higher price is harder to justify for typical users, and its markerless mode still needs refinement.

Speaker’s perspective: The review and all product assessments come from one presenter. He disclosed that Shining 3D provided both scanners free for review, with no payment exchanged.

Rate this summary

Your feedback will help improve summaries.

Improve this summary

Reprocess with a stronger model when the summary feels incomplete or inaccurate.

Pro

Translate summary in another language

Pro

Ask questions to this video

Chat for follow-up questions, clarifications, and source-backed answers.

Coming soon

Share this summary

Original video