Video summary

Building Prototypes Part 12 of 18 Plastics Forming and Casting

Main summary

Key takeaways

Educational

Summary

The video demonstrates two ways to make plastic parts: vacuum forming and replicating parts with silicone molds. The presenter also explains how vacuum casting can reduce bubbles and how silicone molds can be used for some metal castings.

1. Vacuum forming

A heated plastic sheet is clamped in a frame and positioned over a mold. Vacuum draws the sheet down over the mold’s shape. The mold does not need to be airtight: the vacuum spreads around it and pulls the plastic around corners.

The plastic must stay in place until it cools enough to hold its shape.

Lexan (polycarbonate) is difficult to vacuum-form because it does not soften readily and hardens quickly as it cools. The presenter’s Lexan sample therefore does not fully conform to the mold. Other plastics, such as PVC, ABS, and polyethylene, are described as easier to form. They remain soft longer and can conform well, but must be left to cool fully before removal to avoid distortion. Lexan’s advantage is its strength and shatter resistance.

2. Making silicone molds for replicas

Silicone molds are useful when a part needs a good surface finish or material properties that a 3D-printed part may not provide.

Basic mold-making process

  1. Place the original part in a small box or container.
  2. Mix the two-part mold-making silicone and pour it over the part.
  3. Let the silicone cure, then remove the original.
  4. Use the flexible mold to cast a copy.

The mold-making silicone described here differs from ordinary caulking silicone: it does not stick to the original, so mold release is generally unnecessary. Its flexibility also allows it to release undercuts and details such as holes, pins, and screw-head shapes.

The presenter says silicone can reproduce very fine surface details, but notes that its flexibility can make the mold less dimensionally accurate. Embedding a metal screen in the silicone can help stiffen it. The process is especially useful for reproducing surface texture and detail.

3. Degassing and vacuum casting

Air trapped in viscous materials such as silicone and resin can cause bubbles or defects. The presenter recommends vacuum treatment both when preparing the mold material and when casting a part.

Casting a low-bubble replica

  1. Mix the resin according to its instructions. For a high-quality result, degas the resin before casting.
  2. Put the resin in a container with plenty of extra height, since it can foam and rise several times its original height under vacuum.
  3. Place it in a vacuum chamber and wait for bubbles to expand and escape, then subside.
  4. Put the silicone mold in the chamber, with a tube running from the resin into the mold. A guard around the mold can catch any overflow.
  5. Apply vacuum so the resin is drawn through the tube and into the mold.
  6. Pinch off the tube once the mold is full, then release the vacuum. The presenter explains that any small bubbles remaining in the resin tend to collapse as pressure returns.
  7. Remove the setup and cure the resin according to the material’s requirements. The temperature varies by resin; the examples given range roughly from 50–80°C, with silicone requiring a higher temperature in the described case.
  8. Add pigment if a colored cast part is desired.

The finish of a cast replica depends partly on the resin and how it is mixed; the example shown is less glossy than the original.

4. More complex molds and uses

For a part with features on both sides, make a two-part mold. Add registration pins so the halves align, and provide a feed opening for the resin and a vent or air-escape opening.

The method can be used for small or large parts, though larger molds require more material and can become expensive. Other possibilities include:

  • Placing metal inserts in a mold, for example to provide threads.
  • Mixing fillers or chopped carbon fiber into resin.
  • Laying carbon fiber into the mold and impregnating it with resin.

Vacuum impregnation is also useful for waterproofing and strengthening electrical coils and similar components, where trapped air would otherwise remain in the material.

5. Silicone molds for limited metal casting

Some silicone molds can tolerate high temperatures for short periods. The presenter says they can be used to cast zinc alloys and, in some cases, certain aluminum alloys. A mold may produce hundreds of plastic parts but only around ten metal parts, depending on the material and conditions. The resulting zinc-aluminum alloy castings are described as having a good, die-cast-like appearance.

Speakers and sources

One presenter explains and demonstrates the processes. The subtitles do not name the speaker; the video is from Dan Gelbart’s channel.

Rate this summary

Your feedback will help improve summaries.

Improve this summary

Reprocess with a stronger model when the summary feels incomplete or inaccurate.

Pro

Translate summary in another language

Pro

Ask questions to this video

Chat for follow-up questions, clarifications, and source-backed answers.

Coming soon

Share this summary

Original video